Blending Board

I bought myself a blending board for Mother’s Day, which seems like ages ago. A blending board is another tool for preparing fiber for spinning. The main thing it does is make “rolags”, which are rolled up spirals of fiber for spinning. You can also make batts with the blending board. Ironically, one thing it does not do well is “blend” different fibers together. A drum carder works more efficiently for making larger batts and for thoroughly blending fibers together.

My new blending board

When I was ready to try out the blending board, I went to my fiber stash closet and picked out some different fibers and colors that looked pretty together. You can see below a bag of blue superwash wool (that I purchased in 2009 according to the label), a bag with some turquoise dyed angora rabbit, some darker turquoise alpaca fiber, and some orange, green and purple dyed bamboo.

Fiber from my stash to make rolags

I decided to just go for it without measuring or having a plan. I had watched a couple of you tube videos to learn how to use the blending board, so I knew the basics. I started applying some of the blue wool first, and them some of the alpaca and angora rabbit. You just swipe some on, dragging down so it spreads out, rather than being lumpy. A special brush is used to compact the fiber down so you have room to add more, or you can use a paintbrush. It took some practice to figure how much fiber to add on each layer, and to feel comfortable with the technique so that it came out evenly. It does not have to be even, it can be any way you like it. But I find it easier to spin if the fiber is somewhat evenly distributed, rather than having thick blobs here and there.

Some fiber applied to the blending board

I applied a layer of fiber, brushed it down, then applied another layer. I continued to add more layers and brush it down until the blending board was pretty full. I could have fit more fiber on, but decided to stop and remove the fiber into a rolag. The following series of photos shows the blending board after each layer of fiber was applied.

My hands got scratched up in the process of “pasting” the fiber on to the board. I did not see any references to this on the videos I watched. To get the fiber off the blending board and into a rolag, you wrap the fiber around two dowels starting at the bottom. Rather than lifting it all off in one big roll, you are supposed to lift it and pull part of it off on to the dowel, then start again to get more. I got too much fiber on the first rolag, and then it all started to come off the board before I got it rolled on the dowel. I had to start over brushing some of the fiber back onto the blending board, so the last rolag is thinner and blended differently.

Rolling the fiber off the blending board on to two dowels

I was able to make five rolags of varying thickness.

Rolags completed and ready to spin

The total weight of the five rolags is 48 grams. Maybe I should have measured the fiber out at the beginning to an even 50 grams, which is a typical weight for a small ball of yarn. The first rolag has much more fiber in it, the last one is the smallest. The rolags look nice in the photo, but I think I can do a better job of making them more even on my next try.

To spin a rolag, you start at one end and draw the fiber out in a spiral.

A rolag ready to spin

I got busy with other things for awhile (mainly knitting and ripping out and re-knitting sections of the Sea & Sky Shrug), so I did not spin for several weeks. Meanwhile I heard about a 21 day spinning event called the “Tour de Fleece” taking place from June 26 to July 18 and coinciding with the Tour de France bike race. I decided to make an effort to participate virtually.

From the Tour de Fleece facebook page: “The idea is to set yourself a challenge. It doesn’t matter what the challenge is — it could be spinning fine for the first time, or producing an artsy fartsy yarn as an exercise, it could be spinning enough for a specific project. If you’ve always wanted to spin a little every day (say, a spinning meditation practice), but never seem to find time for it, perhaps that could be the challenge — spinning every morning of the tour. What matters is you set out the challenge, and meet it during the specified time”.

My challenge was to practice making rolags with the blending board, and to actually spin every day during this period. It was a nice idea, but I am afraid I failed miserably, as other priorities came up. We had company coming and going, there were summer outside chores, the shrug was more important, etc. Oh well some other time I can set myself a new spinning goal. In the next photos you can see the five rolags spun on to two bobbins, and then plied together into a skein of yarn.

Two bobbins of singles spun from the rolags
Plying the singles together
Wound on to the nitty noddy

The final result was a small skein of yarn. It is not really big enough to make anything, but it looks very pretty sitting in a ceramic bowl.

Finished skein of yarn spun from rolags

Published by Meg Hanson

Hello. I am a recently retired empty nester. My husband and I moved to Jewett Lake in Otter Tail County, Minnesota, after living most of our lives in the Minneapolis area. I have no trouble keeping busy with knitting and spinning of wool, selling yarn and handmade goods, reading, walking, watching movies, surfing on the internet, traveling, doing bookkeeping for our family cabin, and spending time with family.

12 thoughts on “Blending Board

  1. The yarn looks beautiful! The colors are so soft. What an interesting process! Forgive me for being behind on my reading. I thought of you when we went to the Amana Colonies. There is a store there The Woolen Mill which still has a working woolen mill. We didn’t make it to that store, but it is on the list for next time. Your work is very impressive, and I like the idea of a virtual event in which to participate. I can see how such an event would be helpful. Do you know what you will make with that yarn?

    Liked by 2 people

    1. Betty,

      I am very behind on my blog reading and responding too. We were in Chicago for our son’s wedding this past weekend. It was wonderful! and now we are back home and back to reality, and catching up on stuff that I did not do while we were gone. The Woolen Mill sounds very interesting, I would want to do that for sure. I don’t know what I will make with the yarn I made from the blending board rolags. It is a pretty small amount, so it might have to be some trim on a larger project. Meanwhile it looks pretty just sitting there!

      Liked by 1 person

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: